With the D-Link Port Fast Ethernet Unmanaged Switches, you can easily expand your business or home network by adding more computers and devices, . View and Download D-Link DESD – Switch manual online. Port 10/ Mbsp Ethernet Switch. DESD – Switch Network Router pdf manual. View and Download D-Link DESD user manual online. D-Link System 10/ NWay Ethernet/ Fast Ethernet Switch User’s Guide DESD. DESD .
|Country:||Saint Kitts and Nevis|
|Published (Last):||7 December 2013|
|PDF File Size:||16.4 Mb|
|ePub File Size:||2.66 Mb|
|Price:||Free* [*Free Regsitration Required]|
This section will explain how to connect Ethernet devices to your new D-Link switch and how to mount the switch.
The site where you install the switch may greatly affect its performance. Please follow these guidelines for setting up the switch. Do not place heavy objects on the switch. Leave at least 10 cm 4 inches of space at the front and rear of the switch for ventilation.
D-Link DES-1016D – Switch Manual
The rubber feet cushion the switch, protect the casing from scratches, and prevent it from scratching other surfaces. Two mounting ears are provided for this purpose. Make d-llnk that the front panel is exposed in order to view the LEDs. Please refer to the following illustrations:.
D-Link DES-1016D User Manual
Attach the ears to each side of the switch, using the screw-holes maunal on the side of the device. Firmly attach the ears to the rack as shown. Please follow the usual safety precautions for rack-mountable products. Use rubber feet provided. In addition, care should be taken not to locate the switch next to, on top of, or underneath any device that generates a significant amount of heat.
For the switch to perform at its optimal level, the switch must have adequate ventilation to prevent the switch from overheating and becoming damaged.
To power on the switch, Plug-in the female connector of the provided power cord into this socket, and the male side of the cord into a suitable power source. As a precaution, in the event of a power failure, unplug the switch. When power is resumed, plug the switch back in. The end node can be connected to any of the ports of the switch. A blinking LED on the bottom indicates packet activity on that port. The following shows the LED indicators for the switch along with an explanation of each indicator.
Comprehensive LED indicators manial the conditions of the switch and status of the network. This green indicator illuminates steadily when a port is connected to a station successfully and has a good link. The indicator will blink to indicate that a port is transmitting or receiving data on the network. This indicator is amber-colored when the port is connected to a MbpsFast Ethernet station.
It is green when the port is connected to a Mbps Ethernet station.
It is not illuminated when the port d-ljnk connected to a 10Mbps Ethernet station. Switch power input is provided by and internal universal power supply VAC: The AC power connector is a standard three-pronged connector that supports the power cord.
Please see the Power On section below for instructions on how to properly connect the switch to a power source. A common problem when connecting different gigabit devices is Auto-sensing between the two different ports. When connecting two Gigabit devices it is imperative that the port speed be set the same on both sides. If the link speed is not 1.
If the cable is pinned improperly, than the network connection will not run at gigabit speeds. Gigabit over copper uses all 8 wires of the Ethernet cable. Isolate each portion of the possible problem, until you des-016d able to find the defective port on the network.
This can be done by des-106d known good gigabit ports, and cabling. The configuration for all scenarios is listed below. Gigabit switches and NICs will always use a straight through Ethernet cable when connecting two devices together.
There is no such thing as an dea-1016d Gigabit port, or a crossover Gigabit cable. How to fix slow webpage load speeds on DIRL when used with some mobile devices? The status light on the Dees-1016d router is flashing what is it indicating?
D-LINK DESD – SWITCH MANUAL Pdf Download.
How to hard reset D-Link Wireless router to default mznual The status light on D-Link router is flashing what is it indicating? Get complete infor …. Before You Connect to the Network The site where you install the switch may greatly affect its performance.
D-LINK DESD USER MANUAL Pdf Download.
Please refer to the following illustrations: Attaching the Rubber Feet Use rubber feet provided. Power On To power on the switch, Plug-in the female connector of the provided power dl-ink into this socket, and the male side of the cord into a suitable power source. After the Switch is powered on, the LED indicators will blink briefly while the system resets.
Power Failure As a precaution, in the event of a power failure, unplug the switch.
Power Indicator This green indicator illuminates when the switch is receiving power. The power cable connection is located on the rear panel of the switch.
How do I uplink to another hub or switch?