IPMP CONFIGURATION IN SOLARIS 10 PDF

These topics include IPv4 and IPv6 network configuration, managing TCP/IP 1. Oracle Solaris TCP/IP Protocol Suite (Overview) The default is 10 seconds. Oracle Solaris Administration: IP Services Oracle Solaris 10 1/13 Information An IPMP configuration typically consists of two or more physical interfaces on the . For IPMP configuration tasks, refer to Chapter 31, Administering IPMP (Tasks). Oracle Solaris IPMP involves the following software: You can configure one of the interfaces down to 10 megabits and still place the two interfaces into the.

Author: Kajisho Zulurg
Country: Uzbekistan
Language: English (Spanish)
Genre: Art
Published (Last): 17 April 2010
Pages: 45
PDF File Size: 8.35 Mb
ePub File Size: 20.18 Mb
ISBN: 331-6-22643-765-1
Downloads: 75647
Price: Free* [*Free Regsitration Required]
Uploader: Douzil

IPv6 in Depth Reference. After detecting that a NIC has been repaired, IPMP performs failbackthe process of switching network access back to the repaired interface. An active interface is a physical interface that oslaris both data traffic and probe traffic.

This chapter contains the following information: You do not need to mark an IPv6 test address as deprecated to prevent applications from using the test address. The probe messages help to determine the health of each interface in the IPMP group. Your email address will not be published.

When an interface is considered repaired, any addresses that failed over to another interface then fail back to the repaired interface.

The following are two common types of IPMP configurations: Check the IPv6 configuration.

Multicast memberships also fail over from hme0 to hme1. Verify the ifconfig output as well.

How to configure Solaris 10 Probe based IPMP

However, IPMP does impose the following requirements on your network configuration and topology: Here i have removed the LAN cable from eg1 and let see what happens. IPMP does cnfiguration permit you to add a data address to an interface that is configured through the ifconfig command as standby.

  FVR K7S PDF

If an interface in the group fails solaria is removed for maintenance, IPMP automatically migrates, or fails overthe failed interface’s IP addresses. When a failure occurs, the data addresses on the failed interface migrate to the standby interface.

The failover process ensures uninterrupted access to the network. Configuring an IPv6 Network Tasks 8. If the checks are successful, the data addresses associated with the detached NIC fail over to a functioning NIC in the same group, as if the NIC being detached had failed.

How to configure Solaris 10 IPMP ?

The probes verify that the send and receive path to the interface is working correctly. Leave a Reply Cancel reply Your email address will not be published. RCM has no information regarding how to configure the interface. IPv4 does not use a deprecated address as a source address for any communication, unless an application explicitly binds to the address.

No existing connections are disrupted. Avoid using spaces in group names. You can connect me at – https: The physical interface in an IPMP group is not present at system boot. You can use host routes to explicitly configure a list of target systems to be used by in.

With probe target s defined in the routing table, the in. Fist i am going to disable eg1 and let see what happens. You can always view the current status of an interface by typing ifconfig interface.

You can check the status of an interface by issuing the ifconfig interface command. The port on the switch does not transmit or receive packets.

  ILEO METABOLICO PDF

However, if all of the probe targets on bge0 become unreachable, only bge0 will be congiguration as failed because bge has its own probe targets on its own VLAN. The interface can still be used for probe traffic. Link-local addresses are automatically configured when the ipmpp becomes IPv6-enabled at boot time or when the interface is manually configured through ifconfig.

IPMP provides systems with the ability to detect when an interface has failed. If no routers exist on the link, in. This confighration is often implemented as a device driver and a NIC. U are master of UNIX. Troubleshooting Network Problems Tasks.

How to configure Solaris 10 Probe based IPMP – The Geek Diary

If the cable for bge0 is unplugged, then link-based failure detection will report both bge0 and bge as having instantly failed. For example, to configure hme0 with an IPv6 test address, you would type the following: This process is known as load spreading.

Some failovers might not choose a congiguration interface. Interfaces that are configured with IPMP support two types of addresses: NICs that are not present at system boot represent a comfiguration instance of failure detection.

Also, no failover occurs when all the target systems fail at the same time. An active interface is a physical interface that transmits both data traffic and probe traffic. Suppose you want to create an IPMP group called testgroup1 with the following configuration:. IP Security Architecture Overview. Mobile IP Overview The probing rate depends on the failure detection time FDT.